It’s the most successful shaft fixing in the market place today with a complete selection of both metric and imperial sizes as well as a full selection of weld-on hubs, bolt-on hubs and hub adaptors.
Ease of installation and removal
Equivalent to a shrink-on match upon uniform load applications and thus eliminating the price of a key
No costly reboring: complete selection of both metric and imperial available
Standard range matches up to 125mm/5″ shafts
Special 4-hole feature for balanced assemblies
Complete brief reach range available, for compact lightweight assemblies
High quality, close grain iron (GG25) material
Spherodial Graphite (S.G.) iron building on some sizes to provide increase maximum bores
Manufactured from steel to provide convenient methods to secure fan rotors, metal pulleys, plate sprockets, impellers and so on. to a shaft.
Shouldered outer diameter permits easy location
A convenient methods to secure fan rotors, steel pulleys, plate sprockets, impellers etc to a shaft
Welding not necessary
For use with parallel bore eliminating the price of drilling, tapping and taper boring
Keyed version also designed for heavy duty applications
Installing a Taper Lock bush, including Martin or Fenner Taper Lock bush elements, is as follows:
Screws should be tightened alternately and evenly until all screws are pulled up and the bushing is square into the hub.
The Taper Lock bush needs to be thoroughly cleaned, removing all traces of oil, grease, dirt, and metal filings. Clean the shaft, the bore, the exterior of the bushing, and the bore of the hub where the bush is usually to be set up into, ensuring the bush is removed from the hub, should it already be installed.
Examine the bushing to make sure all surfaces are clear of nicks and burrs, and guarantee the bushing does not have any indicators of cracking or fatigue. Place the bushing in to the hub and match fifty percent holes to make full holes. It is important to notice that the holes have to be matched, not really the threads. Each hole will become threaded using one side only.
Oil threads, the point of the set screws or threads, and under the mind of the cap screws. Then place the screws loosely in to the holes that are threaded on the hub-side
Make sure that the Taper Lock bush is totally free in the hub, after that slide the assembly onto the shaft and locate in the required position. Insert the properly sized key into the shaft keyway, ensuring the main element is a press fit into the shaft keyway. Ensure there is an air gap between your top of the key and the bushing keyway slot. This will prevent cracking of the bush. IMPORTANT: Make sure that there is no oil or lubricant between your taper externally of the bushing and the taper bore of the hub, to that your bushing has been installed.
Screws should be tightened alternately and evenly until all screws are pulled up and the bushing is sq . into the hub.
Utilizing a hammer and block, or sleeve, against the huge end of the Taper Lock bush will help to avoid damage to the bushing. Lightly tap against the busing to ensure it really is seated squarely. The screws are after that tightened further. A torque wrench is used to tighten the screws on the other hand and evenly until all of them are to the recommended torque setting.
Continue doing this alternate hammering and screw tightening until the specified torque is attained and no longer requires tightening following hammering. IMPORTANT: After a period of running under regular conditions, it is suggested that the application form be reviewed to guarantee the torque configurations of the screws are accurate, , nor need re-tightening.
Fill up the holes that aren’t used in combination with grease or silicone sealant to avoid them from filling with dirt and/or rust.
Removal of a Taper Lock bush, including Martin or Fenner Taper Lock bush components, is as follows:

Remove all screws, essential oil threads, and the idea of the set screws or threads, beneath the mind of the cap screws.
Insert screws into the holes that are threaded upon the bushing side, because shown in Physique 2. In sizes where washers are found under the screw head, be sure to use these washers. Please note that there should end up being one screw left that’s not used when getting rid of the bushing.
Tighten the screws alternately before bushing is loosened in the hub. If the bushing does not loosen immediately, tap on the hub to assist remove.
When installing or removing a Taper Lock bush, it is imperative that simply no lubrication be used between your taper. The existence of lubricant on the tapered surfaces is not desirable, as the taper bushing relies on friction to operate efficiently, and lubricants reduce friction. use industry standard Part Numbers to identify the specifications of every Taper Lock bush or Taper bush.